Refine
Year of publication
Institute
- Fachbereich Luft- und Raumfahrttechnik (798) (remove)
Document Type
- Article (380)
- Conference Proceeding (208)
- Book (107)
- Part of a Book (43)
- Patent (19)
- Report (14)
- Doctoral Thesis (10)
- Conference: Meeting Abstract (6)
- Other (3)
- Conference Poster (2)
Keywords
- Karosseriebau (6)
- Strömungsmaschine (6)
- Turbine (6)
- avalanche (6)
- solar sail (5)
- car body construction (4)
- hydrogen (4)
- snow (4)
- Eisschicht (3)
- GOSSAMER-1 (3)
- Hydrogen (3)
- MASCOT (3)
- Obstacle avoidance (3)
- Sonde (3)
- Strömungsausgleich (3)
- UAV (3)
- Wind Tunnel (3)
- Aeroelasticity (2)
- CFD (2)
- Drinfeld modules (2)
- Flight Test (2)
- Kraftfahrzeugbau (2)
- Leichtbau (2)
- Mars (2)
- Micromix (2)
- NOx emissions (2)
- PCM (2)
- Path planning (2)
- Pitching Moment (2)
- Solar sail (2)
- Spacecraft (2)
- Spaltentlastung (2)
- Sportwagen (2)
- Studentenprojekt (2)
- Trajectory Optimization (2)
- Transcendence (2)
- Virtuelle Fahrzeugentwicklung (2)
- Wave Drag (2)
- combustor development (2)
- fuels (2)
- industrial gas turbine (2)
- multiple NEA rendezvous (2)
- small spacecraft (2)
- t-modules (2)
- 1P hub loads (1)
- Active humidity control (1)
- Actuator disk modelling (1)
- Aerodynamic Drag (1)
- Aircraft design (1)
- Aircraft sizing (1)
- Analogue Environments (1)
- Ansaugsystem (1)
- Antarctic Glaciology (1)
- Antarctica (1)
- Asteroid Deflection (1)
- Atmospheres (1)
- Attitude dynamics (1)
- Autofluoreszenzverfahren (1)
- Automated Optimization (1)
- Automotive safety approach (1)
- Autonomy (1)
- Avalanche (1)
- BET (1)
- Bio-inspired systems (1)
- Blade element method (1)
- Bumblebees (1)
- CFD propeller simulation (1)
- CO2 emission reduction targets (1)
- Capacity Building Higher Education (1)
- Carsharing (1)
- Centrifugal twisting moment (1)
- Certification Rule (1)
- Combustion (1)
- Commercial Vehicle (1)
- Common Rail Injection System (1)
- Correlations (1)
- Cost function (1)
- Crashworthiness (1)
- Cryobot (1)
- DLR-ESTEC GOSSAMER roadmap for solar sailing (1)
- Design rules (1)
- Diesel Engine (1)
- Direkteinblasung (1)
- Drag (1)
- Drag Reduction (1)
- Drag estimation (1)
- Driving cycle recognition (1)
- Dry-low-NOx (DLN) combustion (1)
- Dynamic modeling (1)
- ECMS (1)
- ESATAN (1)
- ESATAN-TMS (1)
- Electrical Flight (1)
- Electrical vehicle (1)
- Electrochemical impedance spectroscopy (1)
- Emissions (1)
- Energy management strategies (1)
- Engine Efficiency (1)
- Epistemische Neugier (1)
- Erasmus+ United (1)
- European Framework and South East Asia (1)
- European Transient Cycle (1)
- Evacuation Rule (1)
- Evolutionary Neurocontrol (1)
- Exoplanet (1)
- Extension–twist coupling (1)
- Extraterrestrial Glaciology (1)
- Fault detection (1)
- Finite element method (1)
- Flame residence time (1)
- Flame temperature (1)
- Flight Mechanics (1)
- Flight Tests (1)
- Flight control (1)
- Flutter (1)
- Friction Drag (1)
- Fuel cell (1)
- Fuel-flexibility (1)
- Full-vehicle crash test (1)
- GEO (1)
- Gas turbine combustion (1)
- Geometry (1)
- Glaciological instruments and methods (1)
- Gossamer (1)
- Gossamer structures (1)
- Green aircraft (1)
- Guide Tube (1)
- Health management system (1)
- High hydrogen combustion (1)
- Higher derivations (1)
- Human factors (1)
- Hybrid Propellants (1)
- Hybrid-electric aircraft (1)
- Hydrogen combustion (1)
- Hydrogen gas turbine (1)
- Hyperdifferentials (1)
- ITS (1)
- Ice Melting (1)
- Ice melting probe (1)
- Ice penetration (1)
- Icy Moons (1)
- Icy moons (1)
- Impedance analysis (1)
- Inflight Regeneration, Recuperation (1)
- Infused Thermal Solutions (1)
- Interplanetary flight (1)
- Interstellar objects (1)
- Jupiter (1)
- Kalman filter (1)
- Karosserieleichtbau (1)
- Karosserietechnik (1)
- LEO (1)
- Ladungswechsel (1)
- Laminare Strömung (1)
- Laminarprofil (1)
- Leading Edge Vortex (1)
- Leichtbauwerkstoffe (1)
- Lichtstreuungsbasierte Instrumente (1)
- Lifting propeller (1)
- Lightweight car body construction (1)
- Local path planning (1)
- Low NOx (1)
- Low emission (1)
- Low-Thrust Propulsion (1)
- Low-field NMR (1)
- Lunar Surface (1)
- MAV (1)
- Mach Number (1)
- Malaysian Automotive Industry (1)
- Malaysian automotive industry (1)
- Materialmischbauweise (1)
- Melting Efficiency (1)
- Melting Performance (1)
- Melting Probe (1)
- Micromix combustion (1)
- Missions (1)
- Multi-objective optimization (1)
- Multidisciplinary Design Optimization (1)
- Multiphase (1)
- Multirotor UAS (1)
- NMR exchange relaxometry (1)
- NOx (1)
- Noise Exposure (1)
- Non-model-based Evaluation (1)
- Nozzle (1)
- Ocean Worlds (1)
- Ocean worlds (1)
- Online diagnostic (1)
- Orbital dynamics (1)
- PEM fuel cell (1)
- PEM fuel cells (1)
- PHILAE (1)
- Parabolized Stability Equation (1)
- Parasitic drag (1)
- Passenger compartment (1)
- Payload (1)
- Periods (1)
- Planetary Protection (1)
- Planetary exploration (1)
- Predictive battery discharge (1)
- Profilumströmung (1)
- Propeller (1)
- Propeller Aerodynamics (1)
- Propeller aerodynamics (1)
- Propeller elasticity (1)
- Propeller performance (1)
- Propeller whirl flutter (1)
- RAMMS (1)
- RaWid (1)
- Relative air humidity (1)
- Reusable Rocket Engines (1)
- Selbstwirksamkeit (1)
- Selective Catalytic Reduction (1)
- Sequence-Search (1)
- Severe Accident (1)
- Small Solar System Body Lander (1)
- Small Spacecraft (1)
- Small spacecraft (1)
- Snow (1)
- Solar Power Sail (1)
- Solar Sail (1)
- Sonic Boom (1)
- Spacecraft Trajectory Optimization (1)
- Spaltentlasung (1)
- Specific Fuel Consumption (1)
- Spectroscopy (1)
- Stahlblech-Leichtmetall Verbundguss (1)
- Stahlblech-Leichtmetall-Hybride (1)
- Statistics (1)
- Strömungssonde (1)
- Subclacial exploration (1)
- Subglacial lakes (1)
- Suction (1)
- Supersonic Flow (1)
- Supersonic Wind Tunnel (1)
- TICTOP (1)
- Technology Challenge (1)
- Technology Transfer (1)
- Thermal Fatigue Testing (1)
- Thermal Model (1)
- Thermal analysis (1)
- Thermal comfort (1)
- Thermal management (1)
- Trajectories (1)
- Transit (1)
- Trapeze effect (1)
- UTeM Engineering Knowledge Transfer Unit (1)
- Unmanned Air Vehicle (1)
- Unmanned aerial vehicles (1)
- Unsteady aerodynamics (1)
- Variable Geometry (1)
- Verbrennungsmotor (1)
- Verbundguss (1)
- Wasserstoff (1)
- Wind milling (1)
- Wind tunnel experiments (1)
- adaptive systems (1)
- aircraft engine (1)
- artificial intelligence (1)
- assistance system (1)
- asteroid lander (1)
- asteroid sample return (1)
- attitude dynamics (1)
- autofluorescence-based detection system (1)
- aviation application (1)
- combustion (1)
- combustor (1)
- contamination (1)
- control system (1)
- debris flow (1)
- eVTOL development (1)
- eVTOL safety (1)
- electrically driven compressors (1)
- electro mobility (1)
- emission (1)
- emission index (1)
- engine demonstration (1)
- flotilla missions (1)
- fuel cell (1)
- fuel cell systems (1)
- fuel cell vehicle (1)
- gamification (1)
- gas turbine (1)
- habitability (1)
- health management systems (1)
- heliosphere (1)
- hybrid laminar flow (1)
- ice moons (1)
- icy moons (1)
- intelligent control (1)
- intelligent energy management (1)
- internal combustion engine (1)
- intrinsische Motivation (1)
- ion propulsion (1)
- latent heat (1)
- lattice (1)
- life detection (1)
- light scattering analysis (1)
- low-thrust (1)
- low-thrust trajectory optimization (1)
- machine learning (1)
- manufacturing (1)
- near-Earth asteroid (1)
- nitric oxides (1)
- operational aspects (1)
- optimization system (1)
- orbit control (1)
- orbital dynamics (1)
- passive thermal control (1)
- planetary defence (1)
- responsive space (1)
- sailcraft (1)
- sample return (1)
- small solar system body characterisation (1)
- small spacecraft asteroid lander (1)
- small spacecraft solar sail (1)
- solar sails (1)
- solar system (1)
- space missions (1)
- star tracker (1)
- subglacial aquatic ecosystems (1)
- subroutine (1)
- subsurface ice (1)
- subsurface ice research (1)
- subsurface probe (1)
- suction structure (1)
- suction systems (1)
- system engineering (1)
- technology transfer (1)
- thermo-physical (1)
- underwater vehicle (1)
- vollvariabler Ventilbetrieb (1)
A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology.
Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures.
On the flight performance impact of landing gear drag reduction methods for unmanned air vehicles
(2018)
The flight performance impact of three different landing gear configurations on a small, fixed-wing UAV is analyzed with a combination of RANS CFD calculations and an incremental flight performance algorithm. A standard fixed landing gear configuration is taken as a baseline, while the influence of retracting the landing gear or applying streamlined fairings is investigated. A retraction leads to a significant parasite drag reduction, while also fairings promise large savings. The increase in lift-to-drag ratio is reduced at high lift coefficients due to the influence of induced drag. All configurations are tested on three different design missions with an incremental flight performance algorithm. A trade-off study is performed using the retracted or faired landing gear's weight increase as a variable. The analysis reveals only small mission performance gains as the aerodynamic improvements are negated by weight penalties. A new workflow for decision-making is presented that allows to estimate if a change in landing gear configuration is beneficial for a small UAV.
The aerodynamic performance of propellers strongly depends on their geometry and, consequently, on aeroelastic deformations. Knowledge of the extent of the impact is crucial for overall aircraft performance. An integrated simulation environment for steady aeroelastic propeller simulations is presented. The simulation environment is applied to determine the impact of elastic deformations on the aerodynamic propeller performance. The aerodynamic module includes a blade element momentum approach to calculate aerodynamic loads. The structural module is based on finite beam elements, according to Timoshenko theory, including moderate deflections. Several fixed-pitch propellers with thin-walled cross sections made of both isotropic and non-isotropic materials are investigated. The essential parameters are varied: diameter, disc loading, sweep, material, rotational, and flight velocity. The relative change of thrust between rigid and elastic blades quantifies the impact of propeller elasticity. Swept propellers of large diameters or low disc loadings can decrease the thrust significantly. High flight velocities and low material stiffness amplify this tendency. Performance calculations without consideration of propeller elasticity can lead to decreased efficiency. To avoid cost- and time-intense redesigns, propeller elasticity should be considered for swept planforms and low disc loadings.
High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation.
Operational Modal Analysis (OMA) is a promising candidate for flutter testing and Structural Health Monitoring (SHM) of aircraft wings that are passively excited by wind loads. However, no studies have been published where OMA is tested in transonic flows, which is the dominant condition for large civil aircraft and is characterized by complex and unique aerodynamic phenomena. We use data from the HIRENASD large-scale wind tunnel experiment to automatically extract modal parameters from an ambiently excited wing operated in the transonic regime using two OMA methods: Stochastic Subspace Identification (SSI) and Frequency Domain Decomposition (FDD). The system response is evaluated based on accelerometer measurements. The excitation is investigated from surface pressure measurements. The forcing function is shown to be non-white, non-stationary and contaminated by narrow-banded transonic disturbances. All these properties violate fundamental OMA assumptions about the forcing function. Despite this, all physical modes in the investigated frequency range were successfully identified, and in addition transonic pressure waves were identified as physical modes as well. The SSI method showed superior identification capabilities for the investigated case. The investigation shows that complex transonic flows can interfere with OMA. This can make existing approaches for modal tracking unsuitable for their application to aircraft wings operated in the transonic flight regime. Approaches to separate the true physical modes from the transonic disturbances are discussed.
We propose a simple parametric OSSD model that describes the variation of the sail film's optical coefficients with time, depending on the sail film's environmental history, i.e., the radiation dose. The primary intention of our model is not to describe the exact behavior of specific film-coating combinations in the real space environment, but to provide a more general parametric framework for describing the general optical degradation behavior of solar sails.
With the increased interest for interstellar exploration after the discovery of exoplanets and the proposal by Breakthrough Starshot, this paper investigates the optimisation of photon-sail trajectories in Alpha Centauri. The prime objective is to find the optimal steering strategy for a photonic sail to get captured around one of the stars after a minimum-time transfer from Earth. By extending the idea of the Breakthrough Starshot project with a deceleration phase upon arrival, the mission’s scientific yield will be increased. As a secondary objective, transfer trajectories between the stars and orbit-raising manoeuvres to explore the habitable zones of the stars are investigated. All trajectories are optimised for minimum time of flight using the trajectory optimisation software InTrance. Depending on the sail technology, interstellar travel times of 77.6-18,790 years can be achieved, which presents an average improvement of 30% with respect to previous work. Still, significant technological development is required to reach and be captured in the Alpha-Centauri system in less than a century. Therefore, a fly-through mission arguably remains the only option for a first exploratory mission to Alpha Centauri, but the enticing results obtained in this work provide perspective for future long-residence missions to our closest neighbouring star system.
Optimization of Interplanetary Rendezvous Trajectories for Solar Sailcraft Using a Neurocontroller
(2002)
Searching optimal interplanetary trajectories for low-thrust spacecraft is usually a difficult and time-consuming task that involves much experience and expert knowledge in astrodynamics and optimal control theory. This is because the convergence behavior of traditional local optimizers, which are based on numerical optimal control methods, depends on an adequate initial guess, which is often hard to find, especially for very-low-thrust trajectories that necessitate many revolutions around the sun. The obtained solutions are typically close to the initial guess that is rarely close to the (unknown) global optimum. Within this paper, trajectory optimization problems are attacked from the perspective of artificial intelligence and machine learning. Inspired by natural archetypes, a smart global method for low-thrust trajectory optimization is proposed that fuses artificial neural networks and evolutionary algorithms into so-called evolutionary neurocontrollers. This novel method runs without an initial guess and does not require the attendance of an expert in astrodynamics and optimal control theory. This paper details how evolutionary neurocontrol works and how it could be implemented. The performance of the method is assessed for three different interplanetary missions with a thrust to mass ratio <0.15mN/kg (solar sail and nuclear electric).
Optical Instruments require an extremely stable thermal surrounding to prevent loss of data quality by misalignments of the instrument components resulting from material deformation due to temperature f luctuations (e.g. from solar intrusion). Phase Change Material (PCM) can be applied as a thermal damper to achieve a more uniform temperature distribution. The challenge of this method is, among others, the integration of PCM into affected areas. If correctly designed, incoming heat is latently absorbed during phase change of the PCM, i.e. the temperature of a structure remains almost constant. In a cold phase, the heat during phase change is released again latently until the PCM returns to its original state of aggregation. Thus, the structure is thermally stabilized. At FH Aachen– University of Applied Sciences research is conducted to apply PCM directly into the structures of affected components (baffles, optical benches, electronic boxes, etc.). Through the application of Additive Manufacturing, the necessary voids are directly printed into these structures and filled later with PCM. Additive Manufacturing enables complex structures that would not have been possible with conservative manufacturing methods. A corresponding Breadboard was developed and manufactured by Selective Laser Melting (SLM). The current state of research includes the handling and analysis of the Breadboard, tests and a correlation of the thermal model. The results have shown analytically and practically that it is possible to use PCM as an integral part of the structure as a thermal damper. The results serve as a basis for the further development of the technology, which should maximize performance and enable the integration of PCM into much more complex structures.
This dataset was acquired at field tests of the steerable ice-melting probe "EnEx-IceMole" (Dachwald et al., 2014). A field test in summer 2014 was used to test the melting probe's system, before the probe was shipped to Antarctica, where, in international cooperation with the MIDGE project, the objective of a sampling mission in the southern hemisphere summer 2014/2015 was to return a clean englacial sample from the subglacial brine reservoir supplying the Blood Falls at Taylor Glacier (Badgeley et al., 2017, German et al., 2021).
The standardized log-files generated by the IceMole during melting operation include more than 100 operational parameters, housekeeping information, and error states, which are reported to the base station in intervals of 4 s. Occasional packet loss in data transmission resulted in a sparse number of increased sampling intervals, which where compensated for by linear interpolation during post processing. The presented dataset is based on a subset of this data: The penetration distance is calculated based on the ice screw drive encoder signal, providing the rate of rotation, and the screw's thread pitch. The melting speed is calculated from the same data, assuming the rate of rotation to be constant over one sampling interval. The contact force is calculated from the longitudinal screw force, which es measured by strain gauges. The used heating power is calculated from binary states of all heating elements, which can only be either switched on or off. Temperatures are measured at each heating element and averaged for three zones (melting head, side-wall heaters and back-plate heaters).
Solar sailcraft provide a wide range of opportunities for high-energy low-cost missions. To date, most mission studies require a rather demanding performance that will not be realized by solar sailcraft of the first generation.
However, even with solar sailcraft of moderate performance, scientifically relevant missions are feasible. This is demonstrated with a Near Earth Asteroid sample return mission and various planetary rendezvous missions.
Die urbane Mobilität ist im Wandel und insbesondere neue innovative Geschäftsmodelle werden einen wesentlichen Teil zur Lösung von künftigen Mobilitätsbedürfnissen beitragen. Die sogenannte „Shared Mobility“ gilt aktuell neben der Elektrifizierung des Antriebes und autonomem Fahrzeugtechnologien als einer der wichtigsten Trendthemen in der Automobilindustrie. Neue Mobilitätsdienstleistungen verlangen dabei verstärkt auch neue Fahrzeugkonzepte.
Solar-electric propulsion (SEP) is superior with
respect to payload capacity, flight time and
flexible launch window to the conventional
interplanetary transfer method using chemical
propulsion combined with gravity assists. This fact
results from the large exhaust velocities of electric
low–thrust propulsion and is favourable also for
missions to the giant planets, Kuiper-belt objects
and even for a heliopause probe (IHP) as shown in
three studies by the authors funded by DLR. They
dealt with a lander for Europa and a sample return
mission from a mainbelt asteroid [1], with the
TANDEM mission [2]; the third recent one
investigates electric propulsion for the transfer to
the edge of the solar system.
All studies are based on triple-junction solar arrays,
on rf-ion thrusters of the qualified RIT-22 type and
they use the intelligent trajectory optimization
program InTrance [3].
Die autonome, unbemannte Luftfahrt ist einer der Schlüsselsektoren für die Zukunft der Luftfahrt. In diesem rasant wachsenden Bereich nehmen senkrecht startende und senkrecht landende Flugzeuge (Vertical Take-Off and Landing – VTOL) einen besonderen Platz ein. Ein VTOL-Flugzeug (manchmal auch „Transitionsfluggerät“ genannt) verbindet die Eigenschaft des Helikopters, überall starten und landen zu können, mit den Geschwindigkeits-, Reichweiten und Flugdauervorteilen des Starrflüglers. Grundsätzlich wird die Senkrechtstart- und -landefähigkeit sowohl von zivilen als auch von militärischen Betreibern unbemannter Fluggeräte (UAVs) gewünscht. Trotzdem bietet der Markt nur eine geringe Anzahl von VTOL-UAVs, da qualitativ hochwertige Entwürfe eine ausgesprochene Herausforderung in der Entwicklung darstellen. An der FH Aachen wird deshalb seit über 5 Jahren an der Auslegung und Analyse von solchen unbemannten VTOL Flugzeugen geforscht. Das neuste Projekt ist der Eigenentwurf einer großen, senkrechtstartenden Transportdrohne. Das „PhoenAIX“ getaufte Fluggerät wird von Falk Götten und Felix Finger im Rahmen einer EFRE-Förderung entwickelt.