Refine
Year of publication
- 2024 (5)
- 2023 (17)
- 2022 (11)
- 2021 (22)
- 2020 (28)
- 2019 (38)
- 2018 (18)
- 2017 (22)
- 2016 (22)
- 2015 (23)
- 2014 (13)
- 2013 (14)
- 2012 (9)
- 2011 (15)
- 2010 (18)
- 2009 (18)
- 2008 (12)
- 2007 (23)
- 2006 (21)
- 2005 (27)
- 2004 (16)
- 2003 (10)
- 2002 (8)
- 2001 (6)
- 2000 (4)
- 1999 (6)
- 1998 (5)
- 1997 (9)
- 1996 (5)
- 1995 (3)
- 1994 (4)
- 1993 (3)
- 1992 (2)
- 1991 (3)
- 1990 (1)
- 1989 (1)
- 1988 (6)
- 1987 (3)
- 1985 (7)
- 1984 (2)
- 1983 (2)
Institute
- Fachbereich Luft- und Raumfahrttechnik (482) (remove)
Has Fulltext
- no (482) (remove)
Language
- English (482) (remove)
Document Type
- Article (239)
- Conference Proceeding (182)
- Part of a Book (26)
- Book (15)
- Conference: Meeting Abstract (7)
- Doctoral Thesis (5)
- Conference Poster (2)
- Other (2)
- Patent (2)
- Preprint (1)
Keywords
- avalanche (6)
- solar sail (5)
- hydrogen (4)
- snow (4)
- GOSSAMER-1 (3)
- Hydrogen (3)
- MASCOT (3)
- Wind Tunnel (3)
- Drinfeld modules (2)
- Flight Test (2)
Wing weight estimation methodology for highly non-planar lifting systems during conceptual design
(2013)
It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility Göttingen of DLR, German Aerospace Center in Göttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.
This paper analyzes the drag characteristics of several landing gear and turret configurations that are representative of unmanned aircraft tricycle landing gears and sensor turrets. A variety of these components were constructed via 3D-printing and analyzed in a wind-tunnel measurement campaign. Both turrets and landing gears were attached to a modular fuselage that supported both isolated components and multiple components at a time. Selected cases were numerically investigated with a Reynolds-averaged Navier-Stokes approach that showed good accuracy when compared to wind-tunnel data. The drag of main gear struts could be significantly reduced via streamlining their cross-sectional shape and keeping load carrying capabilities similar. The attachment of wheels introduced interference effects that increased strut drag moderately but significantly increased wheel drag compared to isolated cases. Very similar behavior was identified for front landing gears. The drag of an electro-optical and infrared sensor turret was found to be much higher than compared to available data of a clean hemisphere-cylinder combination. This turret drag was merely influenced by geometrical features like sensor surfaces and the rotational mechanism. The new data of this study is used to develop simple drag estimation recommendations for main and front landing gear struts and wheels as well as sensor turrets. These recommendations take geometrical considerations and interference effects into account.
This paper examines the positive and negative aspects of a range of interpretations of nearest-neighbours models. Measures-oriented and distributionoriented verification methods are applied to categorial, probabilistic and descriptive interpretations of nearest neighbours used operationally in avalanche forecasting in Scotland and Switzerland. The dependence of skill and accuracy measures on base rate is illustrated. The purpose of the forecast and the definition of events are important variables in determining the quality of the forecast. A discussion of the application of different interpretations in operational avalanche forecasting is presented.
Geochemical characterisation of hypersaline waters is difficult as high concentrations of salts hinder the analysis of constituents at low concentrations, such as trace metals, and the collection of samples for trace metal analysis in natural waters can be easily contaminated. This is particularly the case if samples are collected by non-conventional techniques such as those required for aquatic subglacial environments. In this paper we present the first analysis of a subglacial brine from Taylor Valley, (~ 78°S), Antarctica for the trace metals: Ba, Co, Mo, Rb, Sr, V, and U. Samples were collected englacially using an electrothermal melting probe called the IceMole. This probe uses differential heating of a copper head as well as the probe’s sidewalls and an ice screw at the melting head to move through glacier ice. Detailed blanks, meltwater, and subglacial brine samples were collected to evaluate the impact of the IceMole and the borehole pump, the melting and collection process, filtration, and storage on the geochemistry of the samples collected by this device. Comparisons between melt water profiles through the glacier ice and blank analysis, with published studies on ice geochemistry, suggest the potential for minor contributions of some species Rb, As, Co, Mn, Ni, NH4+, and NO2−+NO3− from the IceMole. The ability to conduct detailed chemical analyses of subglacial fluids collected with melting probes is critical for the future exploration of the hundreds of deep subglacial lakes in Antarctica.