Article
Refine
Year of publication
- 2024 (2)
- 2023 (12)
- 2022 (5)
- 2021 (11)
- 2020 (19)
- 2019 (12)
- 2018 (7)
- 2017 (9)
- 2016 (11)
- 2015 (6)
- 2014 (4)
- 2013 (5)
- 2012 (3)
- 2011 (9)
- 2010 (13)
- 2009 (9)
- 2008 (10)
- 2007 (15)
- 2006 (15)
- 2005 (30)
- 2004 (13)
- 2003 (13)
- 2002 (16)
- 2001 (10)
- 2000 (10)
- 1999 (10)
- 1998 (10)
- 1997 (4)
- 1996 (7)
- 1995 (7)
- 1994 (8)
- 1993 (5)
- 1992 (8)
- 1991 (8)
- 1990 (7)
- 1989 (4)
- 1988 (7)
- 1987 (5)
- 1986 (1)
- 1985 (7)
- 1984 (6)
Document Type
- Article (373) (remove)
Keywords
- avalanche (5)
- snow (3)
- Aeroelasticity (2)
- CFD (2)
- Drinfeld modules (2)
- Karosseriebau (2)
- Kraftfahrzeugbau (2)
- Sportwagen (2)
- Studentenprojekt (2)
- Transcendence (2)
- UAV (2)
- Virtuelle Fahrzeugentwicklung (2)
- car body construction (2)
- t-modules (2)
- 1P hub loads (1)
- Aircraft sizing (1)
- Antarctic Glaciology (1)
- Automotive safety approach (1)
- Autonomy (1)
- Avalanche (1)
Institute
- Fachbereich Luft- und Raumfahrttechnik (373) (remove)
In the friction tests between honeycomb with film adhesive and prepreg, the relative displacement occurs between the film adhesive and the prepreg. The film adhesive does not shift relative to the honeycomb. This is consistent with the core crush behavior where the honeycomb moves together with the film adhesive, as can be seen in Figure 2(a). The pull-through forces of the friction measurements between honeycomb and prepreg at 1 mm deformation are plotted in Figure 17(a). While the friction at 100°C is similar to the friction at 120°C, it decreases significantly at 130°C and exhibits a minimum at 140°C. At 150°C, the friction rises again slightly and then sharply at 160°C. Since the viscosity of the M18/1 prepreg resin drops significantly before it cures [23], the minimum friction at 140°C could result from a minimum viscosity of the mixture of prepreg resin and film adhesive before the bond subsequently cures. Figure 17(b) shows the mean value curve of the friction measurements at 140°C. The error bars, which represent the standard deviation, reveal the good repeatability of the tests. The force curve is approximately horizontal between 1 mm and 2 mm. The friction then slightly rises. As with interlaminar friction measurements, this could be due to the fact that resin is removed by friction and the proportion of boundary lubrication increases. Figure 18 shows the surfaces after the friction measurement. The honeycomb cell walls are clearly visible in the film adhesive. There are areas where the film adhesive is completely removed and the carrier material of the film adhesive becomes visible. In addition, the viscosity of the resin changes as the curing progresses during the friction test. This can also affect the force-displacement curve.
Development and Testing of a Low NOX Micromix Combustion Chamber for an Industrial Gas Turbine
(2017)
The Micromix combustion principle, based on cross-flow mixing of air and hydrogen, promises low emission applications in future gas turbines. The Micromix combustion takes place in several hundreds of miniaturized diffusion-type micro-flames. The major advantage is the inherent safety against flash-back and low NOx-emissions due to a very short residence time of reactants in the flame region. The paper gives insight into the Micromix design and scaling procedure for different energy densities and the interaction of scaling laws and key design drivers in gas turbine integration. Numerical studies, experimental testing, gas turbine integration and interface considerations are evaluated. The aerodynamic stabilization of the miniaturized flamelets and the resulting flow field, flame structure and NOx formation are analysed experimentally and numerically. The results show and confirm the successful adaption of the low NOx Micromix characteristics for a range of different nozzle sizes, energy densities and thermal power output.